Pro duct7 - Bulk Cloned-manufacture,factory,supplier from China

MDF product advantages and development prospects    The surface of MDF is smooth and not easily deformed, the performance is stable, and the edges are relatively strong and firm; the thermal insulation performance is good, and the tensile strength is high. These characteristics are more suitable for furniture manufacturing and interior decoration of construction projects.

Oriented Strand Board Introduction:Oriented strand board (OSB), also called European pine board, is made of small diameter wood, interfelled wood, wood core, board veneer, branch Y wood, etc., and processed into 90-130mm long, 5-30mm wide and 0.5mm thick strands in the direction of wood grain by special planing equipment (long wood planer or two-stage chipping planing equipment), then dried, glued, and formed in the prescribed direction by hot pressing.

    Particleboard is a wood-based panel processed from wood or other non-wood plants. The middle layer of the particle board is wood chips, and the two sides are finely-organized wood chips, which are formed by hot pressing with adhesives and other additives. According to the structure, it can be divided into single-layer, double-layer, and gradient structure particle boards. The surface layer of the particleboard is powder layered, and the particleboard with uniform texture is the best.

Where are the functions of different density boards used?1. Standard board: Standard board is a material with a smooth side and a textured finish. It is used for cabinets, drawer bottoms and wall panels that belong to hidden parts.2. Glazed panel: Glazed panel is the surface layer that has been painted, often pasted with facing bricks or stamped into facing bricks or noodle patterns, used for wall panels or wall panels around bathtubs.3. Plastic veneer: Plastic veneer is used for sliding doors, which is good in decoration and easy to clean.

The reason for the deformation of density board furniture is here?    We all know that MDF has a wide range of applications. However, furniture made of this kind of board often has such a problem: the furniture board is deformed, which is very annoying.It not only seriously affects the normal use of our furniture, but also has a bad influence on family life. We knowThere are many reasons for this problem, and we will introduce them in detail below.1.

Advantages and disadvantages of density boardadvantage:      1. The MDF surface is flat and easy to paint. All kinds of paints and paints can be evenly coated on the density board, which is the first choice for paint effect.      2. Density board is another kind of beautiful decorative board, which is better than solid wood furniture in appearance.      3. All kinds of veneer, printed paper, PVC, gummed paper film, melamine impregnated paper and light metal sheet can be decorated on the surface of MDF.      4.

     It is said that wall panels originated in England in the 16th century. Everyone knows that the climate in England is cold and humid. In order to block the damp and cold lower part of the wall, wall panels are used for insulation.    Another theory goes back to the Netherlands in 1300. At that time, Europe was in the dark Middle Ages, and knights wearing armor and holding long swords often scratched the walls of castles or palaces inadvertently. Protect with wood.     At the beginning, wall panels were mainly used in castles and palaces.

    Medium density fiberboard is a kind of artificial board made from the thinned wood of branches, small diameter wood, fast-growing wood, bamboo and other plant materials with limited wood resources. The comprehensive utilization rate of wood is high, which conforms to China's forestry development policy and is conducive to the implementation of China's forestry sustainable development strategy.Medium density fiberboard DisplayProduct Certificates-SGS,ISO9001,FSC  

FeaturesThe density board surface is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is very decorative. But the density board has poor moisture resistance. In contrast, the nail-holding force of MDF is worse than that of particleboard. If the screws loosen after tightening, it is difficult to fix them at the same position.The main advantage1. Density board is easy to be painted. All kinds of paints and paints can be evenly coated on the density board, which is the first choice for paint effect.2.

Manufacturing Process Broadcast1. Chipping: It is the manufacturing workshop of the raw materials in the whole board production. It mainly cuts loose wood into wood chips that meet the production specifications, so as to provide better conditions for fiber separation in preparation for heat.2. Thermal grinding. The wood chips cut out of the chipping workshop are preheated and cooked, and then mechanically separated to obtain fibers.3. Fiber drying: heat grinding and sizing to make the moisture content of the fiber reach 40%-50%.

Oriented strand board is a new type of high-strength environmental protection board. Under the background of the prominent structural contradiction between the supply and demand of wood in my country and the prevalence of green environmental protection concepts, oriented strand board relies on a wide range of material sources, advanced production technology, and excellent mechanical properties.

FeaturesThe density board surface is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is very decorative. But the density board has poor moisture resistance. In contrast, the nail-holding force of MDF is worse than that of particleboard. If the screws loosen after tightening, it is difficult to fix them at the same position.The main advantage1. Density board is easy to be painted. All kinds of paints and paints can be evenly coated on the density board, which is the first choice for paint effect.2.

  1. The characteristics of density board: the surface of density board is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is decorative. However, density boards have poor moisture resistance, and in comparison, density boards have poorer nail-holding power than particle boards. If the screws loosen after tightening, it is difficult to fix them again due to the low strength of density boards.2. The use of MDF: mainly used for laminate flooring, door panels, partition walls, furniture, etc.

1.

    OSB board is the upgrading of traditional particle board.

The difference between medium density fiberboard and particle board is so bigAbstract: There are many types of man-made panels, and many friends are always unclear when they are decorating. Some friends always can't tell the difference between particleboard and density board. In fact, as long as you know the two kinds of boards, it is very simple to distinguish them.1. MDF and particle board materials are differentParticleboard is processed by high temperature and high pressure after the logs are broken, and the wood chips are the main raw materials.

What is the main reason for the deformation of density board?The main reason for the deformation of the density board is the production process or the storage and use process.1.

    Moldability: Since the MDF is fibrous, it is beneficial for the machine to do carving, molding, radian and other shapes. The molded door panels and European-style lines on the market are all MDF, so MDF is more suitable for the back of the wardrobe and Door panels and moldings.Matters needing attention in making wardrobe with MDF1. From the appearance, check whether the thickness and density are uniform, whether the corners are damaged, whether there are layers, bulges, carbonization, etc., and whether there are soft parts.2.

     Density board, also known as fiberboard, is an artificial board made of wood fiber or other plant fiber by hot pressing after slicing, cooking, fiber separation, and drying, then applying urea-formaldehyde resin or other suitable adhesives.     The biggest advantage of MDF (medium fiberboard) is that it can be used for carving, engraving and milling, so as to make various shapes.

The difference between particleboard and density board:1. Different usesDensity board is mainly used for composite floors, door panels, partition walls, furniture, etc. In home decoration,it is mainly used for surface treatment of mixed oil technology. It can be used as the back panel of the cabinet, but it is not suitable for the cabinet body. Particleboard can be painted and veneered in various ways, and can also be used to make cabinets.2.

    Density board is made by soaking wood, tree branches and other objects in water and then heat-grinding, paving and hot-pressing. It is made of wood fiber or other plant fiber.Man-made panels made by applying urea-formaldehyde resin or other suitable adhesives. Of course, the glue contains two chemicals, benzene and formaldehyde.

The main purpose of MDF FiberboardMainly used for laminate flooring, door panels, partition walls, furniture, etc. MDF is mainly used for surface treatment of oil-mixed technology in home decoration; MDF is generally used for furniture, and high-density boards are used for interior decoration. Exterior decoration, office and civilian furniture, audio, vehicle interior decoration, can also be used as anti-static floor in computer room and production material for wall panels, security doors, wall panels, partitions, etc. It is also a good material for packaging.

What are the advantages and disadvantages of commonly used density boards in the production of showcases?Advantages of MDF1. Because the density board is hard, it is not easy to deform. At the same time, it is not easy to warp because it is made of fine wood chips. At the same time, the MDF for display cabinets has high bending resistance and impact resistance.2.

With the continuous development of science and technology, carbon crystal panels or Black Core MDF, as a new type of decoration material, have gradually attracted people's attention. So, what are the advantages and disadvantages of Black Core MDF in whole house decoration? Let's take a look together.First, the advantages of Black Core MDF1). Environmental protection and healthBlack Core MDF is a kind of non-toxic, tasteless, non-radiation environmental protection material, which will not cause any harm to the human body.